Building A Live Edge Floating Shelf

In this episode, I build a custom floating Shelf with a live edge for a Colorado Home.  The shelf is made from a walnut slab and is adorned with ebony bowties inlaid into a defect in the slab.

Summary

 Transforming a Rough Walnut Slab into a Floating Shelf

I’ve had this walnut slab sitting in my shop for a while, and I finally decided to turn it into a floating shelf. It wasn’t without its challenges—the slab had a rough chainsaw cut where a branch had been removed, and one end was pretty rotten. But I saw potential in its natural cracks, which I planned to highlight with hand-inlaid ebony bow ties.

Flattening the Slab

The live-edge walnut slab had a slight twist and was just a bit too wide for my jointer, so I had to get creative. I used a router sled to flatten one side, then ran it through the planer to smooth out the opposite face. After flipping it back, I cleaned up any remaining marks for a perfectly flat surface.

Shaping the Organic Edge

Next, I power-carved the rough chainsaw-cut edge to create a more natural, flowing shape. I imagined water running off the edge, following the contours of the wood as if it were stone. The initial carving went well, and I refined the curves later with a sander for a smoother finish.

Dealing with the Rotten End

The rotten section needed attention, but instead of cutting it off entirely, I opted to preserve its character. I used a wire brush to remove loose material, then sealed it with resin to stabilize the wood.

Inlaying Ebony Bow Ties

To accentuate the natural cracks, I sketched out several bow tie designs on paper, chose my favorites, and glued the templates onto ebony. After cutting them out on the bandsaw, I cleaned up the edges with a chisel and added a slight bevel to ensure a snug fit.   I secured the bow ties in place using double-sided tape and carefully traced their outlines with a razor blade. Then came the meticulous process of chiseling out the mortises—working from the corners inward to avoid overcutting.

Cutting the Shelf to Size

I decided to angle the cut on one end to make the rotted section a focal point. The idea was to create the illusion that the shelf was emerging from the wall, as if the wood was naturally decaying into it. It was a small artistic touch that added depth to the piece.

Fitting the Shelf to an Uneven Wall

Installing the shelf in a stairwell meant dealing with an out-of-square wall. To simplify the process, I scribed the wall’s shape onto a plywood template, sanded it to fit, and then transferred the profile to the walnut slab. A few adjustments with a block plane ensured a perfect fit.

Mounting Hardware and Final Adjustments

Since the floating shelf hardware required precise placement, I taped kraft paper to the wall to mark stud locations and transferred them to the slab. Using a block of wood as a guide, I drilled straight holes for the mounting brackets and chiseled out recesses for a flush fit.  To fine-tune the shelf’s level, I added countersunk screws along the bottom edge, allowing for minor adjustments. A story stick helped me accurately position the wall-mounted hardware before the final installation.

The Moment of Truth

With everything prepped, it was time to hang the shelf. After a few nervous moments, it slid into place perfectly—floating effortlessly against the wall, with its organic edges, ebony bow ties, and weathered character on full display.

This project was a great reminder that even flawed materials can become stunning pieces with a little patience and creativity. The walnut slab, once rough and uneven, now serves as both a functional shelf and a unique work of art.

More Project Build Videos

Building a Dr. Seuss Inspired Coat Rack

How a straight 4x4 becomes a whimsical, Dr. Seuss-inspired coat rack using a band saw inside-out cutting technique, plus a hand-cut castle joint base.

Building a Fireplace Mantel

In this episode, I designed and built a Craftsman-style fireplace mantel for a client in Colorado Springs.  The mantel was made from hickory and stained to match some of the other millwork in the house.  

Building Modern Contemporary Doors

In this episode, I build a whole house of Modern Contemporary Doors featuring a stainless steel accent for my Colorado Springs client's home.

Asymmetrical Shelf Build

I recently completed an asymmetrical shelf unit for a client, and let me tell you, it was one of those projects that looks simple on the surface but requires serious attention to detail from start to finish.

Installing a Door Lock on a Custom Door

I have installed Door locks of all varieties over the years, from different setback to full mortise locks.  In this episode, I show how to install a door lock and deadbolt set for my custom copper door project.  This was a custom door for a client in Evergreen, Colorado, just outside of Denver.

Building a Nakashima-Inspired Live-Edge Walnut Table

Crafting a live-edge walnut table inspired by the legendary woodworker George Nakashima. The build combines traditional joinery techniques with modern tools, resulting in a piece that balances elegance and functionality. Here’s how I brought this table to life for my Denver Client.

Building a Craftsman Style Bench

I built a Craftsman-style bench with storage.  The design cues for this bench came from my client's Denver home, which was built in the craftsman style.  Specific details I pulled from their home were the rope molding corresponding to the rope bolding in the wainscotting. 

Building a Platform Bed

In this episode, I build a platform bed with a sheepskin headboard for a Colorado Springs Client.  The bed is made from walnut and features four floating shelves attached to the headboard. Each side of the bed has an integrated reading light.

Building a Walnut Vanity with a Live Edge Backspalsh

In this episode, I build a Custom walnut vanity with a live-edge backsplash. This Colorado Springs client wanted a contemporary floating custom vanity with some rustic appeal. To accomplish this, we created a vanity with a beautiful contemporary look and added a live-edge backsplash to give it that Mountain Modern look.  

Custom Wood Inlay on Box Lid

This is a memorial box for a little girl who passed from epilepsy.  Her name is Clair, and the nurses who cared for her called her Clair Bear, so we decided an appropriate inlay was bear.  Each piece of wood was selected for its natural color to tell the story and was inlayed by hand.

Building an Asian Inspired Keepsake Box

In this episode, I build a custom asian inspired keepsake box. The Keepsake box sides are made from bamboo, and the top and legs are cherry. If you are into woodworking and want to make this box, I do have "How To Plans" available for this project.

Building Floating Shelves for a Client’s Master Bath

A client needed a place to display his grandfather's shaving kit and a few other collectibles. Here's how I designed and built the floating shelves to hold them.

Building a Craftsman Style Staircase and Handrail

In this episode, I help a Colorado Springs Client remodel their staircase. The existing staircase was a straight run with an outdated style. I redesigned it to have open-ended steps with a craftsman handrail.

Building a Entry Table With Walnut Cuffs

In this episode, I build a custom entry table with walnut cuffs.  The main table is made from cherry, and the feet are adorned with decorative walnut cuffs.

Learning to Patinate and Bend Metal 

Today's project is more than just building a pendant lamp. I really believe that to continue growing as an artist, you have to always be experimenting, trying new techniques, and working in new mediums.

Building a Scandinavian Round Table

I took my time building this round table. I’m thrilled with the result—a sleek, Scandinavian-inspired table with Midcentury undertones.

Building a Custom Rustic Steel Dining Table Base

Building a custom rustic steel dining table base, from welding and acid treatment to creating unique rust patinas with vinegar and finishing with weighted concrete for stability

Making a Wooden Ice Bucket

Today's project is to build a decorative wooden ice bucket for a bar cart I constructed earlier. This isn't a functional piece meant to hold water; it's a prop, designed solely to add visual interest and character to my home bar setup.

Building a Sculpture that Doubles as a Coat Rack

building a sculptural two-moon coat rack, from grain-matched bandsaw cuts and CNC joinery fixtures to hand-shaped hooks and a hidden wall-mount system.

DIY Barn Door Guide

A while ago, I built a barn door with a steel frame that encased the wood for a client in Denver, Colorado. It turned out great, but one question kept coming up: How did I keep the bottom of the door from swinging around? Most barn door hardware kits include a T-track that gets screwed into the floor, with a slot routed into the bottom of the door for guidance. But since my door had a steel base, routing a groove wasn’t an option.

Shelving

Coat Rack – Wall Hanging With Storage

Foyer Wall Cabinet

Live-edge Floating Shelf from a Walnut Slab

Contemplation Shelf

Floating Shelf To Display a Model Train

Mesquite Floating Shelf

Walnut & Black Steel Bookshelf

Wall-Mounted Mid-Century Modern TV Cabinet